Rockwell-automation 1440-SDM02-01RA XM-124 Standard Dynamic Measuremen User Manual Page 45
- Page / 166
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Rockwell Automation Publication 1440-UM001C-EN-P - May 2014 45
Install the XM-124 Standard Dynamic Measurement Module Chapter 1
Figure 28 - Velocity Sensor and Two Non-contact Sensor Wiring
IMPORTANT
Transducer DC bias is monitored on all signals.
IMPORTANT
A jumper from terminal 22 to terminal 21 is required for channel 2 buffered
output. See
Connect the Buffered Outputs on page 33.
TYPICAL WIRING FOR COIL-BASED VELOCITY SENSOR AND TWO
NON-CONTACT SENSORS TO XM-120/121 DYNAMIC MEASUREMENT MODULE
Pin A - Common
Pin B - Signal
Cable shield not
connected at this end
Shield
0
16
Channel 1 Input Signal
Signal Common
SIG
-24
COM
SIG
-24
COM
17
1
Signal Common
Channel 2 Input Signal
21
22
-24V DC*
20
-24V DC
4
Signal Common
Tach Input Signal
36
13
31
Shield
Shield
* Note: Jumpering terminal 22 to
terminal 21 configures
CH 2 buffer (-24V to 9V)
18
- User Manual 1
- Important User Information 2
- Summary of Changes 3
- New and Updated 3
- Information 3
- Appendix C 9
- Table of Contents 10
- Additional Resources 11
- Measurement Module 13
- Introduction 15
- Module Components 16
- XM Installation 17
- Requirements 17
- Any limited power 18
- Grounding Requirements 19
- Panel/Wall Mount Grounding 20
- 24V Common Grounding 22
- Mount the Terminal Base 23
- Side Connector 26
- Wire the Terminal Base Unit 27
- Connecting Power 30
- Connect the Relay 30
- Connect the Tachometer Signal 32
- Connect the Buffered Outputs 33
- Connect the Transducer 34
- Pin A - Signal 35
- Pin B - Common 35
- Connect a Non-contact Sensor 36
- Connect a Passive Transducer 37
- Pin A - Common 38
- Pin B - Signal 38
- Connect a Powered Sensor 39
- Cable shield not 40
- Connect the 4…20 mA Outputs 47
- Serial Port Connection 48
- DeviceNet Connection 49
- Mount the Module 51
- Set the Module DIP Switch 52
- Switch 2 - Normal/Legacy Mode 53
- Down Position = 0 54
- Electronic Data Sheets 55
- ADR for XM Modules 56
- Power Up the Module 57
- Passwords and Access 61
- Configurations and Commands 61
- Configuring the XM-124 62
- Standard Dynamic 62
- Transducer 63
- Measurement Mode 65
- Signal Processing 66
- Band Measurement Options 71
- Tracking Filter Options 74
- Band Pass Filter Options 75
- Figure 38 - Normal Mode 77
- Table 7 - Alarm Parameters 80
- Relay Parameters 82
- Table 8 - Relay Parameters 83
- 4…20 mA Output Parameters 85
- Triggered Trend Parameters 86
- SU/CD Trend Parameters 87
- I/O Data Tab 89
- Defined Assembly 90
- Custom Assembly 91
- Identity 92
- Firmware Update 93
- View Data 93
- Monitor Data Parameters 94
- Operate the Module 97
- Transition to Program Mode 98
- Reset Switch 99
- XM Services 100
- Invalid Configuration Errors 101
- XM-124 Module I/O Message 101
- Poll Message Format 102
- COS Message Format 104
- Bit-Strobe Message Format 105
- Chapter 3 Operate the Module 106
- Chapter 4 107
- Triggered 107
- Status Indicators 111
- Tachometer Status Indicators 113
- Setpoint Multiplier Indicator 113
- Appendix A Status Indicators 114
- CIP Objects 115
- Instance Attributes 116
- DeviceNet Object 117
- (Class Code 03 117
- Assembly Object 118
- (Class Code 04 118
- Instances 119
- Services 122
- Connection Object 123
- (Class ID 05H) 123
- Discrete Input Point 124
- Object (Class ID 08H) 124
- Analog Input Point 126
- (Class ID 0A 126
- Parameter Object 127
- (Class ID 0F 127
- Class Attributes 128
- Acknowledge Handler 133
- Object (Class ID 2BH) 133
- Alarm Object (Class ID 31DH) 134
- Band Measurement 136
- Object (Class ID 31E 136
- Channel Object 138
- (Class ID 31F 138
- Device Mode Object 140
- (Class ID 320 140
- Overall Measurement 141
- Object (Class ID 322 141
- Relay Object (Class ID 323 142
- Spectrum Waveform 145
- Measurement Object 145
- (Class ID 324 145
- Appendix B CIP Objects 148
- Speed Measurement 151
- Object (Class ID 325 151
- Tachometer Channel 152
- Object (Class ID 326 152
- Transducer Object 154
- (Class ID 328 154
- Vector Measurement 155
- Object (Class ID 329 155
- 4…20 mA Output 157
- Object (Class ID 32A 157
- History of Changes 159
- Appendix C History of Changes 160
- Numerics 161
- Rockwell Automation Support 166
- Documentation Feedback 166
Related products and manuals for Equipment Rockwell-automation 1440-SDM02-01RA XM-124 Standard Dynamic Measuremen
Equipment Rockwell-automation 1440-SDM02-01RA XM-124 Standard Dynamic Measuremen User Manual
(20 pages)
(20 pages)
Equipment Rockwell-automation 1492-TIFM16-F-3 Fused Term. Module for use in SIL2 User Manual
(6 pages)
(6 pages)
Equipment Rockwell-automation 1329I Integrated AC Drive/Motor, Series B FRN 3.X User Manual
(80 pages)
(80 pages)
Equipment Rockwell-automation 1512A MV Controllers, 400A One-High Cabinet, Stand User Manual
(96 pages)
(96 pages)
Equipment Rockwell-automation 1494D Flange Mounted Circuit Breaker Operators - 1 User Manual
(5 pages)
(5 pages)
Equipment Rockwell-automation 1404-M4_M5_M6_M8 Powermonitor 3000 Installation In User Manual
(66 pages)
(66 pages)
Equipment Rockwell-automation 1404-DM, W40863-850-01 Display Module Cable Instal User Manual
(2 pages)
(2 pages)
Equipment Rockwell-automation 1609 Industrial Uninterruptible Power Supply - Ser User Manual
(8 pages)
(8 pages)
© 2020, manymanuals.com. All rights reserved. | 0.108 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals