Rockwell-automation GV3000/SE AC Bookshelf Drive Hardware Ref, Install User Manual Page 22
- Page / 96
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
2-8
GV3000/SE AC Bookshelf Drive Hardware Reference, Version 6.06
Step 7. Locate jumper J4 on the Regulator board. Refer to figure 2.6.
Step 8. Locate pin 1 on jumper J4. Move the jumper to the desired setting as shown
in figure 2.7.
Step 9. Reattach the cover. For 24 to 43 A drives, reattach the front panel before
reattaching the cover.
Important: Check that the display cable is reconnected to the Regulator board. You
will need to fold and route the cable under the heatsink before replacing
the cover.
Step 10. Reconnect wiring to the faceplate of the drive.
Step 11. Reapply input power.
Step 12. Verify that Terminal Strip Analog Input Offset (P.009), Terminal Strip Analog
Input Gain (P.010), and Terminal Strip Analog Input Configure (P.011) are
correctly set.
Note that the jumper settings must match the software settings; otherwise,
the reference value may differ from what is expected. Refer to the
GV3000/SE Bookshelf Drive Software Start-Up and Reference manual for
more information.
2.6.1.2 Setting the Analog Output Jumper (J17)
Jumper J17 is the analog output jumper. This jumper selects either a 0-10 VDC or
4-20 mA scaled signal output that is programmable to be proportional to either speed
or torque using parameter P.012. Refer to the GV3000/SE Bookshelf Drive Software
Start-Up and Reference manual for more information about this parameter. The
analog output signal is available through the terminal strip.
The jumper only selects a 0-10 VDC source voltage or 4-20 mA sink current to
represent speed or torque. Note that the 4-20 mA current selection requires an
external 12 VDC power supply for operation as shown in table 7.6.
Use the following procedure to set jumper J17:
Figure 2.7 – Jumper J4 Settings for Analog Input Speed Reference
Current Input Option
Pins 1-2
0-20 mA
J4
V
In
C
In
Volta
g
e Input Option
Pins 2-3
10 VDC
J4
(Default)
V
In
C
In
!
ATTENTION:DC bus capacitors retain hazardous voltages after input
power has been disconnected. After disconnecting input power, wait five
(5) minutes for the DC bus capacitors to discharge and then check the
voltage with a voltmeter to ensure the DC bus capacitors are discharged
before touching any internal components. Failure to observe this
precaution could result in severe bodily injury or loss of life.
- GV3000/SE AC Bookshelf Drive 1
- Important User Information 2
- Document Update 3
- Summary of Changes 5
- Contents 7
- List of Figures 9
- List of Tables 11
- Introduction 13
- About the Drive 15
- Locations 17
- Component Locations 18
- (Default) 22
- 2.7 Keypad/Display 25
- 2.11 Optional Equipment 26
- PROFIBUS 27
- Planning Before Installing 29
- Motor Full Load Amps 37
- 4.1 Mounting the Drive 39
- 4.3 Grounding the Drive 40
- PE L1 L2 L3 43
- 45 47 48 U V W 43
- Installing Input Power Wiring 45
- Disconnect 46
- Drive’s Power Terminals 46
- Supplied 47
- CHAPTER 6 49
- Wiring the Regulator Board 51
- Terminal Strip and the 51
- Output Relay Terminal Strip 51
- Function Loss 53
- Start/Stop 53
- 7.1 Stopping the Drive 54
- (FVC Regulation Only) 55
- If P.027 = 1 61
- Forward Direction Only 61
- Wiring Optional User-Supplied 65
- Braking Resistors 65
- Completing the Installation 69
- Troubleshooting the Drive 71
- 10.6 Replacement Parts 77
- Technical Specifications 79
- Standard EN 60204-1:1992 83
- Compatibility Standards 85
- C.3 Wiring Practices 86
- C.3.1 Motor Leads 87
- C.3.2 Grounding the Drive 87
- Stranded copper wire 88
- Plastic insulation 88
- Inner plastic sheath 88
- Outer plastic jacket 88
- Table C.1 – Encoder Cabling 89
Related products and manuals for Equipment Rockwell-automation GV3000/SE AC Bookshelf Drive Hardware Ref, Install
Equipment Rockwell-automation 1756-Enxxx_Ewxxx EtherNet/IP Modules Installation User Manual
(104 pages)
(104 pages)
Equipment Rockwell-automation Ethernet Design Considerations Reference Manual User Manual
(106 pages)
(106 pages)
Equipment Rockwell-automation T7485 ICS Regent+Plus Isolated Guarded Output Modu User Manual
(20 pages)
(20 pages)
Equipment Rockwell-automation T8402 Trusted Dual 24V dc Digital Input Module - 6 User Manual
(30 pages)
(30 pages)
© 2020, manymanuals.com. All rights reserved. | 7.023 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals