Rockwell-automation 20-750-PNET2P Profinet Dual Port Option Module User Manual Page 25
- Page / 100
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Rockwell Automation Publication 750COM-UM007A-EN-P - January 2013 25
Installing the Option Module Chapter 2
Table 1 - Drive and Option Module Start-Up Status Indications
After verifying correct operation, swing down the drive HIM bezel to its closed
position and install the drive cover. For more details on status indicator
operation, see page 56
and page 57.
Item Name Color State Description
Drive STS Indicator
➊
STS
(Status)
Green Flashing Drive ready but not running, and no faults are present.
Steady Drive running, no faults are present.
Yellow Flashing When running, a type 2 (non-configurable alarm condition exists – drive continues to run.
When stopped, a start inhibit condition exists and the drive cannot be started (see drive
parameter 933 - [Start Inhibits]).
Steady A type 1 (user configurable) alarm condition exists, but the drive continues to run.
Red Flashing A major fault has occurred. Drive will stop. Drive cannot be started until fault condition is
cleared.
Steady A non-resettable fault has occurred.
Red/Yellow Flashing Alternately A minor fault has occurred. Use drive parameter 950 - [Minor Flt Config] to enable. If not
enabled, acts like a major fault. When running, the drive continues to run. System is
brought to a stop under system control. The fault must be cleared to continue.
Yellow/Green Flashing Alternately When running, a type 1 alarm exists.
Green/Red Flashing Alternately Drive firmware is updating.
Option Module Status Indicators
➋
PORT — Off The option module is not powered or connected properly to the drive.
Red Flashing The option module is not receiving any communication from drive.
Steady The option module detected a duplicate or invalid port ID.
Green Flashing Normal operation. The option module is establishing communication with drive. It will
turn steady green or red.
Steady Normal operation. The option module is properly connected and communicating with the
drive.
Orange Steady The brand of the option module and drive do not match.
➌
MOD — Off The option module is not powered or connected properly to the drive.
Red Flashing The option module has failed the firmware test or a firmware update is in progress.
Steady The option module has failed the hardware test.
Green Flashing Normal operation. The option module is operating but is not transferring I/O data to a
controller.
Steady The option module is operating and is transferring I/O data.
➍
➎
NET A
NET B
— Off The option module cannot establish network communication or has experienced a
communication timeout.
Red Flashing The option module has detected a network configuration error.
Steady The option module has experienced an internal network controller error (ERTEC 200 Self-
Test failure).
Green Steady Normal operation. The option module is properly connected and communicating on the
network.
- User Manual 1
- Important User Information 2
- Summary of Changes 3
- Table of Contents 5
- Appendix C 7
- Logic Command/Status Words: 7
- PowerFlex 750-Series Drives 7
- Glossary 7
- Conventions Used in This 9
- Rockwell Automation 9
- Related Documentation 10
- Getting Started 11
- Features 12
- Understanding Parameter 13
- Compatible Products 13
- Required Equipment 13
- User-Supplied Equipment 14
- Safety Precautions 16
- Quick Start 17
- Installing the Option Module 19
- Setting the IP Address 20
- Selection Jumper 20
- Connecting the Option 21
- Module to the Drive 21
- Module to the Network 22
- Using MRP (Media 23
- Redundancy Protocol) for 23
- Ring Topology 23
- Applying Power 24
- and page 57 25
- Configuring the Option Module 29
- Disabled 0 30
- 0<<1 30
- 0 << 255 31
- Setting a Master-Slave 32
- Hierarchy (Optional) 32
- Enable Datalinks To Read Data 34
- Setting a Fault Action 35
- Setting Web Page Access 37
- 0<<2 38
- Restoring Option Module 39
- Parameters to Factory 39
- Defaults 39
- Viewing the Option Module 40
- Status Using Parameters 40
- Updating the Option 40
- Module Firmware 40
- Example Network 41
- Configure the Profinet 42
- Controller 42
- GSDML Installation 43
- Slave Configuration 44
- Using the I/O 47
- Understanding the Profinet 48
- Scanner I/O Image 48
- Using Logic Command/ 48
- Using Reference/Feedback 49
- Using Datalinks 50
- Acyclic Messaging 51
- Profinet Acyclic Messaging 52
- Example Messaging 52
- Troubleshooting 55
- PORT Status Indicator 56
- MOD Status Indicator 56
- NET A Status Indicator 57
- NET B Status Indicator 57
- Viewing Option Module 58
- Diagnostic Items 58
- Viewing and Clearing 62
- Enabling the Option Module 65
- Web Pages 65
- Viewing the Web Pages 65
- Process Display Pop-up 68
- Dialog Box 68
- Profinet Configuration Web 69
- Configure E-mail 70
- Notification Web Page 70
- 3. Click Save Changes 72
- Figure 12 72
- Device Information Pages 73
- PNET2P option module) 75
- Specifications 77
- Environmental 78
- Regulatory Compliance 78
- Option Module Parameters 79
- About Parameter Numbers 80
- How Parameters Are 80
- Organized 80
- Device Parameters 80
- Host Parameters 83
- 750-Series Drives 87
- Logic Status Word 88
- Rockwell Automation Support 100
- Documentation Feedback 100
Related products and manuals for Equipment Rockwell-automation 20-750-PNET2P Profinet Dual Port Option Module
Equipment Rockwell-automation 160-DN2 160-DN2 DeviceNet Communication Module FRN User Manual
(116 pages)
(116 pages)
Equipment Rockwell-automation 150 SMC-50 Soft Starter Safety Label Installation User Manual
(2 pages)
(2 pages)
(4 pages)
(4 pages)
Equipment Rockwell-automation 140U Q, M Frame CB Alarm Switch and Auxiliary Swit User Manual
(8 pages)
(8 pages)
© 2020, manymanuals.com. All rights reserved. | 6.278 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals