Rockwell-automation 20-750-PNET2P Profinet Dual Port Option Module User Manual Page 80
- Page / 100
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
80 Rockwell Automation Publication 750COM-UM007A-EN-P - January 2013
Appendix B Option Module Parameters
About Parameter Numbers
Each parameter set is independently and consecutively numbered.
How Parameters Are
Organized
The Device Parameters and Host Parameters are separately displayed in a
Numbered List view order.
Device Parameters
Configuration Tool Numbering Scheme
• HIM
• Connected Components Workbench software
• DriveExplorer
• DriveExecutive
The Device parameters and Host parameters
begin with parameter 01. For example, Device
Parameter 01 - [Port Number] and Host
Parameter 01 - [DL From Net 01] are
parameter 01 as indicated by this manual.
• Acyclic Messaging See Chapter 6, Acyclic Messaging for details.
Parameter
No. Name and Description Details
01 [Port Number]
Displays the drive port into which the option
module is installed. Typically, this will be Port 4, 5,
or 6.
Minimum: 4
Maximum: 6
Type: Read Only
02 [DLs From Net Act]
Displays the number of controller-to-drive
Datalinks that the drive is using based on the I/O
connection opened by the controller.
Minimum: 0
Maximum: 16
Type: Read Only
03 [DLs To Net Act]
Displays the number of drive-to-controller
Datalinks that the controller is using based on the
I/O connection opened by the controller.
Minimum: 0
Maximum: 16
Type: Read Only
04 [Net Addr Src]
Displays the source from which the option module
network address is taken. It is either the values of
configured option module Device parameters or
from a DCP-DHCP server.
Values: 0 = DCP-DHCP
1 = Config
Type: Read Only
05 [Reset Module]
No action if set to ‘0’ (Ready). Resets the option
module if set to ‘1’ (Reset Module). Restores the
option module to its factory default settings if set
to ‘2’ (Set Defaults). This parameter is a command.
It will be reset to ‘0’ (Ready) after the command
has been performed.
When performing a Set Defaults, the drive may
detect a conflict. If this occurs, the drive will not
allow a Set Defaults action. You must resolve the
conflict before attempting a Set Defaults action for
the option module.
Default: 0 = Ready
Values: 0 = Ready
1 = Reset Module
2 = Set Defaults
Type: Read/Write
Reset Required: No
ATTENTION: Risk of injury or equipment damage exists. If the option
module is transmitting I/O that controls the drive, the drive may fault
when you reset the option module. Determine how your drive will
respond before resetting the option module.
- User Manual 1
- Important User Information 2
- Summary of Changes 3
- Table of Contents 5
- Appendix C 7
- Logic Command/Status Words: 7
- PowerFlex 750-Series Drives 7
- Glossary 7
- Conventions Used in This 9
- Rockwell Automation 9
- Related Documentation 10
- Getting Started 11
- Features 12
- Understanding Parameter 13
- Compatible Products 13
- Required Equipment 13
- User-Supplied Equipment 14
- Safety Precautions 16
- Quick Start 17
- Installing the Option Module 19
- Setting the IP Address 20
- Selection Jumper 20
- Connecting the Option 21
- Module to the Drive 21
- Module to the Network 22
- Using MRP (Media 23
- Redundancy Protocol) for 23
- Ring Topology 23
- Applying Power 24
- and page 57 25
- Configuring the Option Module 29
- Disabled 0 30
- 0<<1 30
- 0 << 255 31
- Setting a Master-Slave 32
- Hierarchy (Optional) 32
- Enable Datalinks To Read Data 34
- Setting a Fault Action 35
- Setting Web Page Access 37
- 0<<2 38
- Restoring Option Module 39
- Parameters to Factory 39
- Defaults 39
- Viewing the Option Module 40
- Status Using Parameters 40
- Updating the Option 40
- Module Firmware 40
- Example Network 41
- Configure the Profinet 42
- Controller 42
- GSDML Installation 43
- Slave Configuration 44
- Using the I/O 47
- Understanding the Profinet 48
- Scanner I/O Image 48
- Using Logic Command/ 48
- Using Reference/Feedback 49
- Using Datalinks 50
- Acyclic Messaging 51
- Profinet Acyclic Messaging 52
- Example Messaging 52
- Troubleshooting 55
- PORT Status Indicator 56
- MOD Status Indicator 56
- NET A Status Indicator 57
- NET B Status Indicator 57
- Viewing Option Module 58
- Diagnostic Items 58
- Viewing and Clearing 62
- Enabling the Option Module 65
- Web Pages 65
- Viewing the Web Pages 65
- Process Display Pop-up 68
- Dialog Box 68
- Profinet Configuration Web 69
- Configure E-mail 70
- Notification Web Page 70
- 3. Click Save Changes 72
- Figure 12 72
- Device Information Pages 73
- PNET2P option module) 75
- Specifications 77
- Environmental 78
- Regulatory Compliance 78
- Option Module Parameters 79
- About Parameter Numbers 80
- How Parameters Are 80
- Organized 80
- Device Parameters 80
- Host Parameters 83
- 750-Series Drives 87
- Logic Status Word 88
- Rockwell Automation Support 100
- Documentation Feedback 100
Related products and manuals for Equipment Rockwell-automation 20-750-PNET2P Profinet Dual Port Option Module
Equipment Rockwell-automation 160-DN2 160-DN2 DeviceNet Communication Module FRN User Manual
(116 pages)
(116 pages)
Equipment Rockwell-automation 150 SMC-50 Soft Starter Safety Label Installation User Manual
(2 pages)
(2 pages)
(4 pages)
(4 pages)
Equipment Rockwell-automation 140U Q, M Frame CB Alarm Switch and Auxiliary Swit User Manual
(8 pages)
(8 pages)
© 2020, manymanuals.com. All rights reserved. | 3.497 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals