Rockwell-automation 20-750-PNET2P Profinet Dual Port Option Module User Manual Page 56
- Page / 100
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
56 Rockwell Automation Publication 750COM-UM007A-EN-P - January 2013
Chapter 7 Troubleshooting
PORT Status Indicator
This red/green bicolor LED indicates the status of the option module’s
connection to the drive as shown in the table below.
MOD Status Indicator
This red/green bicolor LED indicates the status of the option module as shown
in the table below.
Status Cause Corrective Action
Off The option module is not powered or is not
properly connected to the drive.
• Securely connect and ground the option module to the drive by fully
inserting it into the drive port and tightening its two captive screws
to the recommended torque.
• Apply power to the drive.
Flashing Red The option module is not receiving any
communication from the drive.
• Verify that the option module is properly inserted in the drive port.
• Cycle power to the drive.
Steady Red The option module detected a duplicate or invalid
port ID.
Important: Cycle power to the drive after making any of the following
corrections:
• Securely connect and ground the option module to the drive by fully
inserting it into the drive port and tightening its two captive screws
to the recommended torque.
• Configure the option module and drive to use a Datalink that is not
already being used by another peripheral.
Flashing Green The option module is establishing communication
with the drive.
No action required. This status indicator will turn steady green or red.
Steady Green The option module is properly connected and is
communicating with the drive.
No action required.
Steady Orange The brand of the option module and drive do not
match.
Connect the option module to a compatible product of the same brand
(an Allen-Bradley PowerFlex 750-Series drive).
Status Cause Corrective Action
Off The option module is not powered or is not
properly connected to the drive.
• Securely connect and ground the option module to the drive by fully
inserting it into the drive port and tightening its two captive screws
to the recommended torque.
• Apply power to the drive and network.
Flashing Red The option module has failed the firmware test. • Cycle power to the drive. Parameter settings may have been
changed.
• Clear faults in the option module.
• If cycling power does not correct the problem, the option module
parameter settings may have been corrupted. Reset defaults and
reconfigure the option module.
• If resetting defaults does not correct the problem, update the option
module with the latest firmware revision.
Steady Red The option module has failed the hardware test. • Cycle power to the drive.
• Replace the option module.
Flashing Green The option module is operational, but is not
transferring I/O data.
• Place the Client in RUN mode.
• Configure the option module for the program in the controller.
• Program the controller to recognize and transmit I/O to the option
module.
• Normal behavior if no I/O is being transferred.
Steady Green The option module is operating and is
transferring I/O data to the controller.
No action required.
- User Manual 1
- Important User Information 2
- Summary of Changes 3
- Table of Contents 5
- Appendix C 7
- Logic Command/Status Words: 7
- PowerFlex 750-Series Drives 7
- Glossary 7
- Conventions Used in This 9
- Rockwell Automation 9
- Related Documentation 10
- Getting Started 11
- Features 12
- Understanding Parameter 13
- Compatible Products 13
- Required Equipment 13
- User-Supplied Equipment 14
- Safety Precautions 16
- Quick Start 17
- Installing the Option Module 19
- Setting the IP Address 20
- Selection Jumper 20
- Connecting the Option 21
- Module to the Drive 21
- Module to the Network 22
- Using MRP (Media 23
- Redundancy Protocol) for 23
- Ring Topology 23
- Applying Power 24
- and page 57 25
- Configuring the Option Module 29
- Disabled 0 30
- 0<<1 30
- 0 << 255 31
- Setting a Master-Slave 32
- Hierarchy (Optional) 32
- Enable Datalinks To Read Data 34
- Setting a Fault Action 35
- Setting Web Page Access 37
- 0<<2 38
- Restoring Option Module 39
- Parameters to Factory 39
- Defaults 39
- Viewing the Option Module 40
- Status Using Parameters 40
- Updating the Option 40
- Module Firmware 40
- Example Network 41
- Configure the Profinet 42
- Controller 42
- GSDML Installation 43
- Slave Configuration 44
- Using the I/O 47
- Understanding the Profinet 48
- Scanner I/O Image 48
- Using Logic Command/ 48
- Using Reference/Feedback 49
- Using Datalinks 50
- Acyclic Messaging 51
- Profinet Acyclic Messaging 52
- Example Messaging 52
- Troubleshooting 55
- PORT Status Indicator 56
- MOD Status Indicator 56
- NET A Status Indicator 57
- NET B Status Indicator 57
- Viewing Option Module 58
- Diagnostic Items 58
- Viewing and Clearing 62
- Enabling the Option Module 65
- Web Pages 65
- Viewing the Web Pages 65
- Process Display Pop-up 68
- Dialog Box 68
- Profinet Configuration Web 69
- Configure E-mail 70
- Notification Web Page 70
- 3. Click Save Changes 72
- Figure 12 72
- Device Information Pages 73
- PNET2P option module) 75
- Specifications 77
- Environmental 78
- Regulatory Compliance 78
- Option Module Parameters 79
- About Parameter Numbers 80
- How Parameters Are 80
- Organized 80
- Device Parameters 80
- Host Parameters 83
- 750-Series Drives 87
- Logic Status Word 88
- Rockwell Automation Support 100
- Documentation Feedback 100
Related products and manuals for Equipment Rockwell-automation 20-750-PNET2P Profinet Dual Port Option Module
Equipment Rockwell-automation 160-DN2 160-DN2 DeviceNet Communication Module FRN User Manual
(116 pages)
(116 pages)
Equipment Rockwell-automation 150 SMC-50 Soft Starter Safety Label Installation User Manual
(2 pages)
(2 pages)
(4 pages)
(4 pages)
Equipment Rockwell-automation 140U Q, M Frame CB Alarm Switch and Auxiliary Swit User Manual
(8 pages)
(8 pages)
© 2020, manymanuals.com. All rights reserved. | 0.819 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals