Rockwell-automation 22-COMM-C ControlNet Adapter User Manual Page 75
- Page / 164
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Using Multi-Drive Mode 7-7
The following parameters in each daisy-chained drive must be set to
these values:
Note that the RS-485 network is fixed at 19.2K baud, 8 data bits, no
parity, and 1 stop bit.
Important: Parameter A105 - [Comm Loss Action] in the drives that
are daisy chained is still used in Multi-Drive mode. If the
RS-485 cable is disconnected or broken, the disconnected
drive(s) will immediately take the corresponding Comm
Loss Action(s). Drive parameter A106 - [Comm Loss
Time] is not used in Multi-Drive mode. For a network
disruption, adapter Parameters 08 - [Comm Flt Action]
and 09 - [Idle Flt Action] determine the action taken for
ALL of the drives on the Multi-Drive node.
The following Multi-Drive parameters must be set in the 22-COMM-C:
After setting the 22-COMM-C parameters, set the Operating Mode
Jumper (J7) from “1x” (Single mode) to “5x” (Multi-Drive) operation,
and reset the adapter or cycle power to invoke the change. Refer to
Setting Operating Mode and Node Address Switches
on page 2-1.
Important: The 22-COMM-C parameters can be set using a DSI
peripheral (HIM, DriveExplorer with 22-SCM-232, etc.)
ONLY when the Operating Mode Jumper is in the “1x”
(Single mode) position.
Configuring the RS-485 Network
Parameter Value
P36 - [Start Source] 5 (Comm Port)
P38 - [Speed Reference] 5 (Comm Port)
A103 - [Comm Data Rate] 4 (19.2K)
A104 - [Comm Node Addr] 1-247 (must be unique)
A107 - [Comm Format] 0 (RTU 8-N-1)
Parameter Value
12 - [DSI I/O Cfg] 0 = Drive 0 connected
1 = Drives 0-1 connected
2 = Drives 0-2 connected
3 = Drives 0-3 connected
4 = Drives 0-4 connected
14 - [Drv 0 Addr] Equal to Drive 0 parameter A104 - [Comm Node Address]
15 - [Drv 1 Addr] Equal to Drive 1 parameter A104 - [Comm Node Address]
16 - [Drv 2 Addr] Equal to Drive 2 parameter A104 - [Comm Node Address]
17 - [Drv 3 Addr] Equal to Drive 3 parameter A104 - [Comm Node Address]
18 - [Drv 4 Addr] Equal to Drive 4 parameter A104 - [Comm Node Address]
- ControlNet 1
- Important User Information 2
- Summary of Changes 3
- Table of Contents 5
- Chapter 8 Troubleshooting 6
- Appendix A Specifications 6
- Appendix B Adapter Parameters 6
- About This Manual 9
- Rockwell Automation Support 11
- P-4 About This Manual 12
- Getting Started 13
- Features 14
- Compatible Products 15
- Required Equipment 15
- Safety Precautions 16
- Quick Start 17
- Modes of Operation 18
- Installing the Adapter 19
- Node Address 20
- Switches 20
- Operating 20
- Mode Jumper 20
- Item Description 22
- DSI connector 22
- ControlNet cable 22
- Installing the Adapter 2-5 23
- Applying Power 25
- 2-8 Installing the Adapter 26
- Configuring the Adapter 27
- Using the HIM 28
- Setting the Node Address 29
- Setting the I/O Configuration 29
- Setting a Fault Action 30
- To change the fault action 31
- Resetting the Adapter 32
- Configuring the Adapter 3-7 33
- 3-8 Configuring the Adapter 34
- Configuring the I/O 35
- Configuring the I/O 4-7 41
- 4-10 Configuring the I/O 44
- PLC-5 Example 46
- Using the I/O 51
- Understanding the I/O Image 52
- Using Logic Command/Status 53
- Using Reference/Feedback 53
- ControlLogix Example 55
- 5-6 Using the I/O 56
- Using the I/O 5-7 57
- Using the I/O 5-9 59
- Figure 6.5 59
- 5-10 Using the I/O 60
- Using Explicit Messaging 61
- Ladder Logic Program 65
- Using Multi-Drive Mode 69
- 1 drive per node 70
- System Wiring 72
- 7-6 Using Multi-Drive Mode 74
- Adapter Settings 76
- Drive Settings 76
- ControlLogix I/O Example 77
- 7-10 Using Multi-Drive Mode 78
- 7-12 Using Multi-Drive Mode 80
- Using Multi-Drive Mode 7-13 81
- 7-14 Using Multi-Drive Mode 82
- Using Multi-Drive Mode 7-15 83
- 7-16 Using Multi-Drive Mode 84
- Using Multi-Drive Mode 7-17 85
- 7-18 Using Multi-Drive Mode 86
- Using Multi-Drive Mode 7-19 87
- 7-20 Using Multi-Drive Mode 88
- Using Multi-Drive Mode 7-21 89
- PLC-5 I/O Example 92
- Using Multi-Drive Mode 7-25 93
- 7-26 Using Multi-Drive Mode 94
- Using Multi-Drive Mode 7-27 95
- 7-28 Using Multi-Drive Mode 96
- Using Multi-Drive Mode 7-29 97
- 7-30 Using Multi-Drive Mode 98
- Using Multi-Drive Mode 7-31 99
- 7-32 Using Multi-Drive Mode 100
- Using Multi-Drive Mode 7-33 101
- 7-34 Using Multi-Drive Mode 102
- Using Multi-Drive Mode 7-35 103
- Additional Information 104
- Troubleshooting 105
- PORT Status Indicator 106
- MOD Status Indicator 107
- 8-4 Troubleshooting 108
- Troubleshooting 8-5 109
- (version 3.01 or higher) 109
- 8-6 Troubleshooting 110
- Viewing and Clearing Events 111
- 8-8 Troubleshooting 112
- Specifications 113
- Environmental 114
- Regulatory Compliance 114
- Adapter Parameters 115
- B-2 Adapter Parameters 116
- Adapter Parameters B-3 117
- B-4 Adapter Parameters 118
- ControlNet Objects 119
- Identity Object 120
- Identity Object (Continued) 121
- Assembly Object 122
- Assembly Object (Continued) 123
- Register Object 124
- Register Object (Continued) 125
- Parameter Object 127
- Parameter Object (Continued) 128
- Class Code 130
- Services 130
- Instances 130
- Class Attributes 130
- Instance Attributes 131
- (Continued) 131
- PCCC Object 132
- PCCC Object (Continued) 133
- DSI Device Object 138
- DSI Device Object (Continued) 139
- DSI Parameter Object 141
- Descriptor Attributes 143
- Formulas for Converting 144
- Common Services 144
- Object Specific Services 144
- DSI Fault Object 145
- DSI Fault Object (Continued) 146
- DSI Diagnostic Object 147
- Logic Command/Status Words 149
- Logic Status Word 150
- Glossary 151
- D Data Rate 152
- F Fault Action 153
- I I/O Data 153
- L Logic Command/Logic Status 154
- N Node Address 154
- R Reference/Feedback 154
- S Scanner 155
- Z Zero Data 155
- G-6 Glossary 156
Related products and manuals for Equipment Rockwell-automation 22-COMM-C ControlNet Adapter
Equipment Rockwell-automation 20L PowerFlex 700L Frame 2 Common Mode Choke Kit User Manual
(4 pages)
(4 pages)
Equipment Rockwell-automation 20P PowerFlex DC Drive - Frame C AC Line Snubber B User Manual
(16 pages)
(16 pages)
Equipment Rockwell-automation 20P PowerFlex DC Drive - Frame B Pulse Transformer User Manual
(4 pages)
(4 pages)
Equipment Rockwell-automation 20P PowerFlex DC Drive - Frame C Bimetal Thermosta User Manual
(16 pages)
(16 pages)
Equipment Rockwell-automation 140A Manual Motor Starter / Circuit Breaker Instru User Manual
(4 pages)
(4 pages)
Equipment Rockwell-automation 20P PowerFlex DC Drive - Frame D Snubber Resistors User Manual
(10 pages)
(10 pages)
Equipment Rockwell-automation 20P PowerFlex DC Drive - Frame D Overvoltage Clipp User Manual
(4 pages)
(4 pages)
Equipment Rockwell-automation 20P PowerFlex DC Drive - Frame A Field SCR/Dual Di User Manual
(14 pages)
(14 pages)
Equipment Rockwell-automation 20L-LL PowerFlex 700L Liquid-to-Liquid Heat Exchan User Manual
(6 pages)
(6 pages)
Equipment Rockwell-automation 23P PowerFlex DC Stand-Alone Regulator (SAR) Disch User Manual
(10 pages)
(10 pages)
Equipment Rockwell-automation 42GNC_NF_NL_NP_NR_NU SmartSight DeviceNet PHOTOSWI User Manual
(4 pages)
(4 pages)
© 2020, manymanuals.com. All rights reserved. | 0.628 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals