Rockwell-automation 56RF RFID System User Manual User Manual Page 39
- Page / 156
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Rockwell Automation Publication 56RF-UM001A-EN-P - October 2011 39
EtherNet/IP Addressing Chapter 4
Advanced IP Addresses
The following steps show how to change the IP address from the fundamental
192.168.1.xxx to an advanced address. This assumes the Bul. 56RF interface
block was already set up with an IP address using the network address switches.
The examples below show the change process using specific addresses. The user is
not limited to these addresses; the user can select any address that meets their
needs. In the example below, we change from 192.168.1.115 to 192.168.2.115.
1. Set address switches to 888 and cycle the power.
On the Bul. 56RF interface block, the address switches had previously
been to 115. Set the address switch settings to 888. Cycle the power and
wait until the MOD indicator is blinking red. The MOD indicator blinks
red once, green once, then solid red for a short while, then blinks green
once, and finally blinks red continuously (about once each second). This
takes about 10 seconds after power is restored. The interface block is reset
to its factory setting.
2. Set the address switches to 999 and cycle the power.
On the Bul. 56RF interface block, set the address switch settings to 999.
Cycle the power and wait until the MOD indicator is solid green. The
MOD indicator blinks red once, green once, solid red for a short while and
finally turns solid green. This takes about 10 seconds after power is
restored. The interface block IP address is reset.
3. Use BootP/DHCP Server to set new address
Use the Rockwell BootP/DHCP Server utility to assign a valid address to
the interface block. From the Start button, select Programs >
RockwellSoftware > BOOTP-DHCP Server > BOOTP-DHCP Server.
When power is restored, the interface block repeatedly broadcasts its
MACID and requests an IP address. The BOOTP-DHCP server displays
the MACID in the Request History panel.
- RFID Systems 1
- Important User Information 2
- Table of Contents 3
- Who Should Use this Manual 7
- Purpose of this Manual 7
- Abbreviations 7
- Additional Resources 8
- Backward Compatibility 10
- System Setup 11
- Chapter 1 Introduction 12
- RFID Components 13
- LED Indicators 14
- Transceivers 15
- RFID Tags 16
- Tag Memory Structure 17
- Table 6 - AFI Examples 18
- Table 7 - SLI Tags 19
- EAS Function 20
- Application Family Identifier 20
- Write Access Conditions 21
- Smart Label IC – Lean (SLI-L) 23
- Table 15 - Structure of FB 24
- Handheld Reader/Writer 25
- Component Catalog Number 26
- Accessories 27
- EtherNet/IP 28
- Handheld Interface 28
- Handheld Accessories 28
- Electrical Installation 29
- Auxiliary Power Connection 30
- Power Connection Options 31
- EtherNet I/P Connection 33
- EtherNet/IP Addressing 35
- Figure 10 - Linear Topology 36
- Figure 11 - DLR Topology 37
- Setting the Network Address 38
- Fundamental IP Addresses: 38
- 192.168.1.xxx 38
- Advanced IP Addresses 39
- Change IP Address from One 42
- Advanced Address to another 42
- Advanced Address 42
- IP Address 888 44
- Mechanical Installation 45
- Misalignment (mm) 47
- RSLogix5000 Program 49
- 5. Click New Module 50
- General Tab 51
- EtherNet Address 52
- Module Definition 53
- Connection Tab 53
- Module Info 54
- Internet Protocol Tab 55
- Port Configuration Tab 55
- RSLogix 5000 Controller Tags 57
- Input Image Table and Tags 59
- Input Channel Tags 60
- Table 17 - Allowable Commands 61
- Output Image Table and Tags 62
- Output Channel Tags 62
- Commands Summary 65
- RSLogix 5000 Code Examples 67
- Example Command Routines 68
- - Overview 68
- Clear Multiple Bytes 70
- Get Multiple Block Security 72
- Get System Information 73
- Get Version Information 75
- Inventory 77
- Lock AFI 80
- Lock Block 82
- Lock DSFID 84
- Read Byte Command 85
- Multi-Tag Block Read 88
- Read Single Block 92
- Read Transceiver Settings 94
- Write AFI 96
- Write Byte Command 97
- Write DSFID 99
- Example Routine 100
- Example Results 100
- Write Multiple Blocks 101
- 4 488816 101
- Multi-Tag Block Write 103
- Write Single Block 106
- Stop Continuous Read 108
- Teach Continuous Read 108
- Continuous Read Mode 108
- SLC Code Examples 109
- SLC Code Examples Chapter 10 111
- Chapter 10 SLC Code Examples 112
- MicroLogix 1400 Code Examples 113
- Write Byte 115
- Read Multiple Blocks 115
- Input Image Layout 117
- Output Image Layout 117
- RFID Tag Speed 119
- Command Objective 120
- Operation 120
- Modes of Operation 121
- Mode Overview 122
- Command Structure 122
- RFID Interface Block Web Page 125
- Diagnostics 126
- Network Settings 126
- EtherNet Statistics 127
- I/O Connections 127
- Configuration 127
- Device Identity 128
- Network Configuration 128
- Device Services 128
- Appendix 129
- Error Codes 129
- CIP Information 131
- Identity Object Class Code 132
- Assembly Object Class 134
- Code 0x0004 134
- Reading the Input Image 135
- Table of a 56RF-IN-IPD22 135
- Input Image (56RF-IN-IPD22) 136
- Input Image (56RF-IN-IPD22A) 137
- Input Image (56RF-IN-IPS12) 138
- Writing to the Output Image 139
- Class 1 Connections 143
- Exclusive Owner 143
- Connection 143
- Input Only Connection 144
- Listen Only Connection 144
- Class 3 Connections 144
- Discrete Input Point Object 145
- Class Code 0x0008 145
- Discrete Output Point 146
- Object Class Code 0x0009 146
- Introduction 149
- Click Next 150
- Click Install 151
- Troubleshooting 153
- Rockwell Automation Support 156
- Documentation Feedback 156
Related products and manuals for Equipment Rockwell-automation 56RF RFID System User Manual
Equipment Rockwell-automation 20D-RES-A0 PowerFlex 700S Resolver Feedback Option User Manual
(16 pages)
(16 pages)
Equipment Rockwell-automation 42FB-xxx General Purpose and Analog Output DIN Fib User Manual
(4 pages)
(4 pages)
Equipment Rockwell-automation 22B PowerFlex 40/400/40P IP30/NEMA 1 for Comm Opti User Manual
(2 pages)
Equipment Rockwell-automation 42JT VisiSight Photoelectric Polarized Retroreflec User Manual
(4 pages)
(4 pages)
Equipment Rockwell-automation 20P PowerFlex DC Drive - Frame B Bimetal Thermosta User Manual
(16 pages)
(16 pages)
Equipment Rockwell-automation 23P PowerFlex DC Stand-Alone Regulator (SAR) Field User Manual
(10 pages)
(10 pages)
Equipment Rockwell-automation 20Y Lifting and Mounting PowerFlex Active Front En User Manual
(6 pages)
(6 pages)
Equipment Rockwell-automation 22-HIM-C2S PowerFlex 4-Class HIM (DSI) Quick Refer User Manual
(4 pages)
(4 pages)
Equipment Rockwell-automation 140G-KTFx_KTHx_KTIx_KTKx Trip Unit Installation-14 User Manual
(6 pages)
(6 pages)
Equipment Rockwell-automation 23P PowerFlex DC Stand-Alone Regulator (SAR) Fan A User Manual
(6 pages)
(6 pages)
© 2020, manymanuals.com. All rights reserved. | 0.702 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals