Rockwell-automation 20D PowerFlex 700S Phase II Drive Frames 1...6 Ins User Manual download pdf (Page 32)

32 Rockwell Automation Publication 20D-IN024C-EN-P - July 2013

PowerFlex 700S Adjustable Frequency AC Drive - Phase II Control

Frame

Voltage

Code

Current

Rating

Factory Default Jumper Settings Power Source Type

MOV/Input Filter

Caps

(1)(2)

DC Bus Common

Mode Caps

6 B

All Two green/yellow

wires connected

Power Terminal

Block “PE”

Green/yellow wire to

CM Cap Board is

connected

to Power

Terminal Block “PE”

Solid Ground

1. The green/yellow CM Cap jumper wire should

be connected to “PE.”

2. The MOV/Input Filter Cap jumper wires should

be connected to “PE.”

Non-Solid Ground

1. The green/yellow CM Cap jumper wire should

be insulated from ground. If necessary, remove

the jumper wire from “PE” and insulate/secure

it to guard against unintentional contact with

chassis or components. Important: Do Not

Remove/Disconnect the larger green/

yellow wire.

2. MOV/Input Filter Cap jumper wires should be

insulated from ground. If necessary, remove

the jumper wires from “PE” and individually

insulate/ secure each jumper wire to guard

against unintentional contact with chassis or

components.

All Two green/yellow

wires connected

Power Terminal

Block “PE” and

chassis

Green/yellow wire to

CM Cap Board is

connected

to Power

Terminal Block “PE”

Solid Ground

1. The green/yellow CM Cap and MOV jumper

wires should be connected to “PE.”

2. The Input Filter Cap jumper wire (top right)

should be connected to chassis ground with a

metal screw. Verify. If necessary, remove the

nylon screw/spacer and insert a metal M5 x 10

screw. Torque to 3.2 N•m (28 lb•in).

Non-Solid Ground

1. The green/yellow CM Cap and MOV jumper

wires should be insulated from ground. If

necessary, remove them from “PE” and

individually insulate/secure each jumper wire

to guard against unintentional contact with

chassis or components. Important: Do Not

Remove/Disconnect the larger green/

yellow wire.

2. The Input Filter Cap jumper wire (top right)

should be insulated from ground with a nylon

screw/spacer. Verify. If necessary, remove the

metal screw and insert a M5 x 15 nylon screw/

spacer.

(1) AC input drives only. MOV’s and input filter caps do not exist on DC input drives.

(2) When removing MOV’s, the input filter capacitor must also be removed.

DC–DC+BR1BR2

USE 75 C COPPER WIRE ONLY, TORQUE 52 IN-LB (6 N-M)

22-10

AWG

5.3 IN-LB

(0.6 N-M)

WIRE STRIP

PS+

PS–

USE 75 C

COPPER WIRE

ONLY

TORQUE

52 IN-LB

(6 N-M)

INPUTOUTPUT

PE PE

Optional

Communications

Module

PE PE

MOV

Input Filter Cap

CM Cap

DO NOT

REMOVE

MOV

DC–DC+BR1BR2

USE 75 C COPPER WIRE ONLY, TORQUE 52 IN-LB (6 N-M)

22-10

AWG

5.3 IN-LB

(0.6 N-M)

WIRE STRIP

PS+

PS–

USE 75 C

COPPER WIRE

ONLY

TORQUE

52 IN-LB

(6 N-M)

INPUTOUTPUT

PE PE

Optional

Communications

Module

Input Filter Cap

PE PE

MOV

CM Cap

DO NOT

REMOVE

MOV

1 2 ... 27 28 29 30 31 32 33 34 35 36 37 ... 79 80

Comments to this Manuals

No comments

Rockwell-automation 20D PowerFlex 700S Phase II Drive Frames 1...6 Ins User Manual Page 32

Comments to this Manuals

Related products and manuals for Equipment Rockwell-automation 20D PowerFlex 700S Phase II Drive Frames 1...6 Ins