Rockwell-automation 193-EC4 EC4 Current Monitoring Relay User Manual User Manual Page 36
- Page / 157
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Rockwell Automation Publication 193-UM011A-EN-P - September 2010 37
Protective Trip and Warning Functions Chapter 3
Overcurrent Warning
The EC4 Current Monitoring Relay will issue a warning with an overcurrent
condition if:
• The current in any of the phases exceeds the current specified for the
corresponding OC Warn Level parameter (Parameter 120 for L1,
parameter 123 for L2, & parameter 126 for L3)
• No warning condition already exists
If an overcurrent warning parameter is satisfied, the following will occur:
• The TRIP/WARN LED will flash a yellow blinking pattern depending on
which phase encountered the overcurrent warning condition
– 5 blinks for L1 overcurrent
– 6 blinks for L2 overcurrent
– 7 blinks for L3 overcurrent
• Parameter 15, Warning Status, will change
– Bit 4 will go to "1" for L1 overcurrent
– Bit 5 will go to "1" for L2 overcurrent
– Bit 6 will go to "1" for L3 overcurrent
• Bit _ in Parameter 21, Device Status, will go to "1"
Overcurrent Trip
The EC4 Current Monitoring Relay will trip with an overcurrent indication if:
• The current in any of the phases exceeds the current specified for the
corresponding OC Trip Level parameter (Parameter 118 for L1, parameter
121 for L2, & parameter 124 for L3)
• No trip currently exists
If the EC4 Current Monitoring Relay trips on an overcurrent condition, the
following will occur:
Table 11 - Overcurrent Setting Ranges
Current Range [A] Min. [A] Max. [A] Default [A]
0.4…2 0.4 2.5 0.4
1…5 1 6.25 1
3…15 3 18.75 3
5…25 5 31.25 5
9…45 9 56.25 9
18…90 18 112.5 18
9…5000 9 6250 9
- EC4 Current Monitoring Relay 1
- Important User Information 2
- IMPORTANT 3
- DNET-UM072_-EN-P 4
- Table of Contents 5
- Product Overview 10
- Diagnostic Parameters 12
- Trip Relay 12
- Inputs and Outputs 12
- Status Indication 13
- Test/Reset Button 13
- Node Address Switches 14
- DeviceNet Compatibility 14
- Flash Memory 14
- Installation and Wiring 15
- Starter Installation 16
- Starter Assembly Instructions 17
- 193-EC_ _E) 18
- Cat. No. 193-EC_ _B) 20
- Cat. No. 193-EC_ _E) 21
- Power Terminals 22
- Terminal Designations 23
- Grounding 24
- Short-Circuit Ratings 24
- Fuse Coordination 25
- Typical Motor Connections 25
- Single-Phase Full-Voltage 26
- External Line Current 27
- Transformer Application 27
- Installation Instructions 28
- External Ground Fault 29
- Sensor Application 29
- E3 Plus Overload Relay 30
- Cat. No. 193-CBCT_ 30
- Ground Fault Sensor 30
- Cat. No. 193-CBCT1 31
- Typical Control Circuit 32
- Wiring Diagrams 32
- Single-Phase 33
- Three-Phase 33
- Warning Enable 35
- Overcurrent Protection 35
- Introduction 35
- Trip Enable 35
- Overcurrent Warning 36
- Overcurrent Trip 36
- Ground Fault Protection 37
- Ground Fault Setting Range 38
- Ground Fault Trip 38
- Ground Fault Trip Inhibit 39
- Ground Fault Warning 39
- Undercurrent Protection 40
- Undercurrent Trip 41
- Communication Fault 42
- Protection 42
- Communication Idle 43
- Comm Idle Warning 44
- Remote Trip 44
- Preventive Maintenance 45
- Diagnostics 45
- Queue Clearing 46
- DeviceNet Node Commissioning 47
- Using RSNetWorx for DeviceNet 48
- Figure 26 - EDS Wizard Screen 50
- Programmable Parameters 57
- Monitor Params (All 58
- Read-Only) 58
- Advanced Setup Group 60
- For Catalog Number 193-EC4ZZ 66
- Reset/Lock Group 71
- DeviceNet Setup Group 72
- Output Setup Group 75
- DeviceLogix Group 79
- Current Monitoring Parameters 81
- Reporting Accuracy 82
- Ground Fault Current 83
- Reporting 83
- Monitor Group 83
- Trip History and Snapshot 90
- Trip History Codes 92
- Warning History Codes 93
- Trip Snapshot 94
- Explicit Messaging 96
- (0x0375) 102
- Using DeviceLogix™ 104
- DeviceLogix Programming 105
- Troubleshooting 110
- Network Status LED 111
- OUT A & OUT B LEDs 111
- DeviceNet Modes of 112
- Operation 112
- Power-Up Sequence 112
- Run Mode 113
- Recoverable Error Mode 113
- Unrecoverable Error Mode 113
- Resetting a Trip 114
- Trip/Warn LED 114
- Procedures 114
- DeviceNet Troubleshooting 115
- Input and Output 115
- ➊ FRN 2.000 and later 116
- Specifications 117
- Table 4 - Input Ratings 118
- Environmental 119
- Table 9 - Protection 120
- DeviceNet Information 122
- Identity Object – Class 123
- Code 0x01 123
- Message Router – Class 124
- Code 0x02 124
- DeviceNet Object – Class 124
- Code 0x03 124
- Assembly Object – Class 125
- Code 0x04 125
- Input Assemblies 126
- Connection Object – Class 128
- Code 0x05 128
- Discrete Input Point Object 132
- – Class Code 0x08 132
- Discrete Output Point 132
- Object – Class Code 0x09 132
- Parameter Object – Class 133
- Code 0x0F 133
- Parameter Group Object – 135
- Class Code 0x10 135
- Control Supervisor Object – 139
- Class Code 0x29 139
- Acknowledge Handler 142
- Object – 0x2B 142
- DeviceNet Interface Object 143
- – Class Code 0xB4 143
- ODVA Fault Codes 144
- Logic Supervisor Object 145
- CLASS CODE 0x030E 145
- Status Object - CLASS 145
- CODE 0x0375 145
- CE Compliance 148
- Low Voltage Directive 149
- Two-Speed Applications 150
- Accessories 151
- Rockwell Automation Support 157
- Documentation Feedback 157
Related products and manuals for Equipment Rockwell-automation 193-EC4 EC4 Current Monitoring Relay User Manual
Equipment Rockwell-automation 150-CF147 SMC-3 (43-85A)/SMC-Delta (74-147A) Soft User Manual
(1 pages)
(1 pages)
Equipment Rockwell-automation 592-ECxxx E3 and E3 Plus Solid State Overload Rela User Manual
(4 pages)
(4 pages)
Equipment Rockwell-automation 193-EEGF Bul 193 Overload Relay Application and In User Manual
(6 pages)
(6 pages)
Equipment Rockwell-automation 599-GR4_GR5 Service Disconnect Ground Kit for Bul User Manual
(1 pages)
(1 pages)
Equipment Rockwell-automation 440R MSR45E Safety Relay Expansion Module User Man User Manual
(12 pages)
(12 pages)
Equipment Rockwell-automation 140G-G-EP3/4_H-EP3/4_I-EP3/4_J-EP3/4 Flange for Sw User Manual
(2 pages)
(2 pages)
Equipment Rockwell-automation 592-EUTB_EUTC_EUTD_EUTE Eutectic Overload Relay In User Manual
(2 pages)
(2 pages)
Equipment Rockwell-automation 140U-K-NVMxxx NFPA 79 Internal Rotary Operating NF User Manual
(4 pages)
(4 pages)
© 2020, manymanuals.com. All rights reserved. | 5.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals