Rockwell-automation 193-EC1_2_3_5, 193-ECPM,592-EC1_2_3_5 E3 and E3 Pl User Manual Page 239
- Page / 276
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Rockwell Automation Publication 193-UM002I-EN-P - December 2011 239
DeviceNet™ Information Appendix B
Table 99 - Assembly Object Instance 142 EC5 DeviceLogix Input Assembly
Table 100 - Assembly Object Instance 184 Data Format PNB STATUS
Connection Object – Class
Code 0x05
Multiple instances of the Connection Object are supported. Instance 1 is the
explicit message connection, instance 2 is the polled I/O connection, instance 4 is
the Change of State/Cyclic I/O connection, and instances 5-7 are available for
explicit UCMM connections.
The following Instance 1 (explicit message connection) attributes are supported.
Byte Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
0 Input 4 Input 3 Input 2 Input 1 Out B Stat Out A Stat Warning Tripped
0 Input 6 Input 5
1Network
Output 7
Network
Output 6
Network
Output 5
Network
Output 4
Network
Output 3
Network
Output 2
Network
Output 1
Network
Output 0
2 DLogix
Enabled
Network
Output 14
Network
Output 13
Network
Output 12
Network
Output 11
Network
Output 10
Network
Output 9
Network
Output 8
Byte Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
0Network
Output 7
Network
Output 6
Network
Output 5
Network
Output 4
Network
Output 3
Network
Output 2
Network
Output 1
Network
Output 0
1 DLogix
Enabled
Network
Output 14
Network
Output 13
Network
Output 12
Network
Output 11
Network
Output 10
Network
Output 9
Network
Output 8
- User Manual 1
- Important User Information 2
- Table of Contents 3
- Functions 4
- 5
- DeviceNet™ Node 6
- Commissioning 6
- IMPORTANT 9
- Product Overview 11
- Parameter Monitoring 13
- Overload Relay Features 14
- User Interface 15
- DeviceNet Compatibility 16
- Flash Memory 16
- Installation & Wiring 17
- General Precautions 18
- Starter Assembly 18
- 35 lb-in 19
- Accessory 193-EIMD shown 20
- Approximate Dimensions 21
- Separate Panel Adapter 24
- Voltage Input Module 26
- Three-Pole Terminal Blocks 27
- Terminal Lug Kits 27
- ·m (5 lb.-in.) 28
- Terminal Designations 29
- Grounding 29
- Short-Circuit Ratings 30
- Fuse Coordination 32
- Table 15 - NEMA Contactors 33
- Typical Motor Connections 34
- External Line Current 34
- Transformer Application 34
- Installation Requirements 35
- L1/1 L2/3 L3/5 36
- T1/2 T2/4 T3/6 36
- Wye Connection with PTs 37
- Delta Connection with PTs 37
- Core Balanced Ground 38
- Fault Sensor 38
- Control Wire Requirements 39
- Figure 19 - 193-CBCT1 40
- Figure 21 - 193-CBCT4 40
- Single-Phase 41
- Three-Phase 41
- Figure 24 - NEMA Nomenclature 42
- Figure 27 - NEMA Nomenclature 43
- Trip Enable 45
- Warning Enable 45
- Overload Protection 45
- FLA Setting 46
- CT Ratio 47
- Trip Class 47
- Trip Curves 47
- Trip Class 5 48
- Trip Class 30 48
- Trip Class 20 48
- Trip Class 10 48
- Auto/Manual Reset 49
- Overload Warning 50
- Phase Loss Protection 51
- Ground Fault Protection (E3 52
- Ground Fault Setting Range 53
- Ground Fault Trip 53
- Ground Fault Trip Inhibit 54
- Ground Fault Warning 55
- Ground Fault Filter 55
- Stall Protection 56
- Jam Protection (High 57
- Overload) 57
- Underload Protection 58
- Underload Warning 59
- PTC Trip 61
- Current Imbalance 62
- Current Imbalance Warning 63
- Communication Fault 64
- Communication Idle 65
- Comm Idle Warning 66
- Remote Trip 66
- Voltage Protection 67
- Under Voltage (UV) Warning 68
- Over Voltage (OV) Trip 68
- Voltage Unbalance 69
- Voltage Unbalance Warning 70
- Voltage Rotation Protection 71
- Frequency Protection 72
- Over Frequency (OF) Trip 73
- Over Frequency (OF) Warning 73
- Detection 74
- Real Power (kW) 75
- Over Real Power Trip 76
- Over Real Power Warning 76
- Reactive Power (kVAR) 77
- Apparent Power (kVA) 81
- Under Apparent Power Trip 82
- Under Apparent Power Warning 82
- Over Apparent Power Trip 83
- Over Apparent Power Warning 83
- Power Factor Protection 84
- Preventive Maintenance 91
- Diagnostics (E3 Overload 91
- Relays Series C & Later) 91
- Preventive Maintenance Flags 92
- Queue Clearing 93
- DeviceNet™ Node Commissioning 95
- Using RSNetWorx for DeviceNet 96
- Series C and later 102
- Commissioning the 103
- Protection Functions 103
- Programmable Parameters 105
- 193/592-EC5 only 109
- ➊Min Max 112
- Advanced Setup Group 114
- Reset/Lock Group 123
- DeviceNet Setup Group 125
- Output Setup Group 127
- E3 is Tripped 128
- E3 is Reset from Trip 128
- DeviceLogix Group — E3 Plus 131
- Monitoring Parameters 135
- Reporting Accuracy 136
- Ground Fault Current 137
- Reporting 137
- Diagnostic Parameters 137
- Monitor Group 138
- ➊ Series C and later 141
- Voltage Parameters 147
- Voltage Monitor Group 148
- Voltage Setup Group 151
- Power Parameters 159
- Power Monitor Group 161
- Power Setup Group 171
- Trip History and Snapshot 183
- Trip Snapshot 189
- Trip Snapshot Group 190
- Introduction 193
- I/O Messaging 193
- Explicit Messaging 195
- (0x0375) 201
- • Last Attribute Data 202
- Using DeviceLogix™ 205
- DeviceLogix Programming 206
- Troubleshooting 213
- E3 Plus Model EC5 Only 214
- ➊ — — — 15 No No 214
- ➊ — 16 — — No No 214
- Power-Up Sequence 215
- DeviceNet Modes of 216
- Operation 216
- Resetting a Trip 217
- Trip/Warn LED 218
- Procedures 218
- Loss of Node Address 222
- ➊ FRN 2.000 and later 223
- Specifications 225
- Table 18: Input Ratings 226
- Environmental 227
- Electromagnetic 227
- Compatibility 227
- ➋Environment 2 228
- Protection 229
- DeviceNet™ Information 231
- DeviceNet Objects 232
- Identity Object – Class 233
- Code 0x01 233
- Message Router – Class 234
- Code 0x02 234
- DeviceNet Object – Class 234
- Code 0x03 234
- Assembly Object – Class 235
- Code 0x04 235
- Output Assemblies 236
- Input Assemblies 237
- Connection Object – Class 239
- Code 0x05 239
- Discrete Input Point Object 243
- – Class Code 0x08 243
- Discrete Output Point 243
- Object – Class Code 0x09 243
- Parameter Object – Class 244
- Code 0x0F 244
- Parameter Group Object – 245
- Class Code 0x10 245
- Discrete Output Group 246
- Object - CLASS CODE 246
- Control Supervisor Object 247
- – Class Code 0x29 247
- ➊ E3 Plus Models EC2 and EC3 249
- E3 Plus Model EC5 249
- Object – 0x2B 251
- Overload Object – Class 251
- Code 0x2C 251
- Acknowledge Handler 251
- ➋ FRN 2.000 and later 254
- ➌ FRN 1.003 and earlier 254
- ➍ FRN 3.001 and later 254
- Help Strings 255
- DPI Warning Object 257
- CLASS CODE 0x0098 257
- Warning 46 259
- Warning 47 259
- Warning 48 259
- DeviceNet Interface Object 260
- – Class Code 0xB4 260
- MCC Object - CLASS CODE 261
- Logic Supervisor Object 261
- CLASS CODE 0x030E 261
- E3 Status Object - CLASS 262
- CODE 0x0375 262
- CE Compliance 269
- Low Voltage Directive 270
- Two-Speed Applications 271
- Accessories 273
- Appendix E Accessories 274
- Rockwell Automation Support 276
- Documentation Feedback 276
Related products and manuals for Equipment Rockwell-automation 193-EC1_2_3_5, 193-ECPM,592-EC1_2_3_5 E3 and E3 Pl
(1 pages)
Equipment Rockwell-automation 440P-WM3 Metal Rod Lever Installation/Operating In User Manual
(2 pages)
(2 pages)
Equipment Rockwell-automation 25-COMM-E2P PowerFlex 25-COMM-E2P Dual-Port EtherN User Manual
(172 pages)
(172 pages)
Equipment Rockwell-automation 140MX-C_F Motor Protection Circuit Breaker Accesso User Manual
(1 pages)
(1 pages)
Equipment Rockwell-automation 194E Control and Load Switches 125...315 A, 3 Pole User Manual
(1 pages)
(1 pages)
Equipment Rockwell-automation 140U-xxx NFPA 79 Internal Rotary Operating Handle User Manual
(2 pages)
(2 pages)
© 2020, manymanuals.com. All rights reserved. | 5.306 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals