Rockwell-automation 2711PC-xxxx PanelView Plus Compact User Manual User Manual Page 24
- Page / 132
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
24 Publication 2711PC-UM001A-EN-P - March 2009
Chapter 3 Connecting Power
Removing and Installing the
Power Terminal Block
The terminals are shipped with the power terminal block installed.
You can remove the terminal block for ease of installation, wiring, and
maintenance.
PanelView Plus Compact 400 and 600 Terminals
Follows these steps to remove the terminal block in the PanelView
400 and 600 terminals.
1. Insert the tip of small, flat-blade, screwdriver into the terminal
block access slot.
2. Gently pry the terminal block away from terminal to release the
locking mechanism.
WARNING
Explosion Hazard
Substitution of components may impair suitability for hazardous
locations.
Do not disconnect equipment unless power has been switched
off and area is known to be nonhazardous.
Do not connect or disconnect components unless power has
been switched off.
All wiring must comply with N.E.C. articles 501, 502, 503,
and/or C.E.C. section 18-1J2 as appropriate.
Peripheral equipment must be suitable for the location in which
it is used.
ATTENTION
Do not force terminal blocks into connectors to prevent
potential damage to terminal.
- 2711PC-K4M20D 1
- 2711PC-B4C20D, 2711PC-T6M20D 1
- Important User Information 2
- Table of Contents 3
- Intended Audience 7
- Parts List 7
- Additional Resources 7
- Preface 8
- Overview 9
- Software Support 10
- Hardware Configurations 10
- Displays 11
- Accessories 11
- Chapter 1 Overview 12
- Installing the Terminal 13
- USB Ports 14
- Application Information 15
- Environment and Enclosure 16
- Required Tools 17
- Clearances 17
- Cutout Dimensions 17
- Mount the 400 or 600 18
- Terminal in a Panel 18
- Mount the 1000 Terminal in 20
- Product Dimensions 22
- Connecting Power 23
- Removing and Installing the 24
- Power Terminal Block 24
- Earth/Ground Connection 27
- Connect DC Power 28
- Resetting the Terminals 29
- Configuring the Terminal 31
- Navigation Buttons 33
- Enter or Edit Data 34
- Loading an Application 35
- Running an Application 36
- Application Settings 36
- Terminal Settings 36
- Configuring Communication 37
- Communication Driver 38
- Ethernet Driver 38
- Has no properties to edit 38
- Serial Properties 39
- Configuring Network 41
- Information 41
- Define an Ethernet IP Address 42
- Define Name Server Addresses 44
- Configuring Diagnostics 45
- Remote Log Destination 46
- Message Routing 46
- Managing Files on the 47
- Terminal 47
- List of files stored 48
- Modifying Display Settings 50
- Adjust the Display Contrast 51
- Adjust the Display Intensity 51
- Configure the Screen Saver 52
- Font Linking 53
- Configuring the Keypad 54
- Keyboard, or Mouse 54
- Configuring the Touch 56
- Configuring Print Options 58
- 4. Press OK when done 59
- Configuring Startup Options 60
- Configuring Startup Tests 63
- Clearing the System Event 65
- Displaying Terminal 66
- Displaying 68
- FactoryTalk View ME 68
- Station Information 68
- Modifying the Date, Time 69
- Change the Time Zone 70
- Modifying Regional 71
- Settings 71
- Change the Time Format 72
- Change the Short Date Format 73
- Change the Long Date Format 74
- Chapter Objectives 75
- Precautions 75
- Replacing the Battery 76
- Retaining Tabs 78
- Replacing the Backlight 79
- Backlight 80
- Retaining Tab 80
- Using an External 81
- CompactFlash Card 81
- Removing the Product ID 82
- Replacing the Bezel 83
- Display Module Bezel 84
- Cleaning the 85
- Display Window 85
- Terminal Connections 87
- Communication Port 88
- Isolation 88
- Serial Connections 90
- Modem Connection 91
- Construct a Null Modem Cable 91
- Computer Connections 92
- Ethernet Connections 93
- Ethernet Cable 94
- Security Considerations 94
- Upgrading Firmware 95
- Upgrading Firmware with a 96
- Upgrading Firmware over a 100
- Network Connection 100
- IMPORTANT 104
- Troubleshooting 105
- Isolating the Problem 106
- Check the System Event Log 107
- Perform Extended Diagnostics 107
- Startup Information 108
- Messages 108
- Startup Sequence 109
- Startup Error Messages 110
- Checking Terminal 111
- Components 111
- Ethernet Connection 114
- Hardware Compatibility 115
- Application Does Not Load 115
- Application Does Not Run 116
- Configuration Mode Access 116
- Specifications 117
- Mechanical 118
- Agency Certifications 119
- USB Devices 121
- Appendix B USB Devices 122
- Available Fonts 123
- Machine Edition Fonts CD 124
- Rockwell Automation 132
Related products and manuals for Equipment Rockwell-automation 2711PC-xxxx PanelView Plus Compact User Manual
Equipment Rockwell-automation 2706-P72_P74_P42_P44 Inview Display Firmware Upgra User Manual
(8 pages)
(8 pages)
Equipment Rockwell-automation 1798-PFTP1 FlexArmor PROFIBUS Field Termination Pl User Manual
(8 pages)
(8 pages)
Equipment Rockwell-automation 2085-IQ16_IQ32T 24V DC 16 and 32 Sink/Source Input User Manual
(16 pages)
(16 pages)
Equipment Rockwell-automation 6189V-xxxx Solid State Drive Upgrade Kit for Panel User Manual
(8 pages)
(8 pages)
Equipment Rockwell-automation 2090-Series Circular-DIN Connector Kits, Flange Ki User Manual
(32 pages)
(32 pages)
Equipment Rockwell-automation 2706-PENI_PDNI InView EtherNet/IP Module and InVie User Manual
(53 pages)
(53 pages)
Equipment Rockwell-automation 1797-XXX FLEX Ex System Certification Reference Ma User Manual
(252 pages)
(252 pages)
Equipment Rockwell-automation 6000 PowerFlex Medium Voltage Variable Frequency D User Manual
(98 pages)
(98 pages)
© 2020, manymanuals.com. All rights reserved. | 1.004 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals