Rockwell-automation 22-COMM-C ControlNet Adapter User Manual Page 30
- Page / 164
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
3-4 Configuring the Adapter
4-Class drives that are daisy-chained to the RJ45 (RS-485) port on
Drive 0. When the adapter is externally mounted in a DSI External
Comms Kit, Drives 0 through 4 are daisy-chained to the RJ45
(RS-485) port on the Comms Kit. Refer to Chapter 7
, Using
Multi-Drive Mode for more information.
2. If a drive is enabled, configure the parameters in the drive to accept
the Logic Command and Reference from the adapter. For example,
set a PowerFlex 40 drive’s parameter P036 - [Start Source] and
parameter P038 - [Speed Reference] both to “5” (Comm Port). When
using the adapter in Multi-Drive mode, each daisy-chained drive
requires that additional parameters be set. See Configuring the
RS-485 Network on page 7-7 for these parameters and their settings.
3. Reset the adapter (see Resetting the Adapter on page 3-6).
By default, when communications are disrupted (for example, a cable is
disconnected) or the controller is in program mode, the drive responds
by faulting if it is using I/O from the network. You can configure a
different response to communication disruptions using Parameter 08 -
[Comm Flt Action] and a different response to a controller in program
mode using Parameter 09 - [Idle Flt Action].
Setting a Fault Action
!
ATTENTION: Risk of injury or equipment damage exists.
Parameters 08 - [Comm Flt Action] and 09 - [Idle Flt Action] let you
determine the action of the adapter and connected drive if
communications are disrupted or the controller is in program mode. By
default, these parameters fault the drive. You can set these parameters
so that the drive continues to run. Some ControlNet scanners may
operate differently when a controller is in program mode which could
limit the Idle Fault Action’s operating states. Precautions should be
taken to ensure that the settings of these parameters do not create a risk
of injury or equipment damage. When commissioning the drive, verify
that your system responds correctly to various situations (for example, a
disconnected cable or faulted controller).
- ControlNet 1
- Important User Information 2
- Summary of Changes 3
- Table of Contents 5
- Chapter 8 Troubleshooting 6
- Appendix A Specifications 6
- Appendix B Adapter Parameters 6
- About This Manual 9
- Rockwell Automation Support 11
- P-4 About This Manual 12
- Getting Started 13
- Features 14
- Compatible Products 15
- Required Equipment 15
- Safety Precautions 16
- Quick Start 17
- Modes of Operation 18
- Installing the Adapter 19
- Node Address 20
- Switches 20
- Operating 20
- Mode Jumper 20
- Item Description 22
- DSI connector 22
- ControlNet cable 22
- Installing the Adapter 2-5 23
- Applying Power 25
- 2-8 Installing the Adapter 26
- Configuring the Adapter 27
- Using the HIM 28
- Setting the Node Address 29
- Setting the I/O Configuration 29
- Setting a Fault Action 30
- To change the fault action 31
- Resetting the Adapter 32
- Configuring the Adapter 3-7 33
- 3-8 Configuring the Adapter 34
- Configuring the I/O 35
- Configuring the I/O 4-7 41
- 4-10 Configuring the I/O 44
- PLC-5 Example 46
- Using the I/O 51
- Understanding the I/O Image 52
- Using Logic Command/Status 53
- Using Reference/Feedback 53
- ControlLogix Example 55
- 5-6 Using the I/O 56
- Using the I/O 5-7 57
- Using the I/O 5-9 59
- Figure 6.5 59
- 5-10 Using the I/O 60
- Using Explicit Messaging 61
- Ladder Logic Program 65
- Using Multi-Drive Mode 69
- 1 drive per node 70
- System Wiring 72
- 7-6 Using Multi-Drive Mode 74
- Adapter Settings 76
- Drive Settings 76
- ControlLogix I/O Example 77
- 7-10 Using Multi-Drive Mode 78
- 7-12 Using Multi-Drive Mode 80
- Using Multi-Drive Mode 7-13 81
- 7-14 Using Multi-Drive Mode 82
- Using Multi-Drive Mode 7-15 83
- 7-16 Using Multi-Drive Mode 84
- Using Multi-Drive Mode 7-17 85
- 7-18 Using Multi-Drive Mode 86
- Using Multi-Drive Mode 7-19 87
- 7-20 Using Multi-Drive Mode 88
- Using Multi-Drive Mode 7-21 89
- PLC-5 I/O Example 92
- Using Multi-Drive Mode 7-25 93
- 7-26 Using Multi-Drive Mode 94
- Using Multi-Drive Mode 7-27 95
- 7-28 Using Multi-Drive Mode 96
- Using Multi-Drive Mode 7-29 97
- 7-30 Using Multi-Drive Mode 98
- Using Multi-Drive Mode 7-31 99
- 7-32 Using Multi-Drive Mode 100
- Using Multi-Drive Mode 7-33 101
- 7-34 Using Multi-Drive Mode 102
- Using Multi-Drive Mode 7-35 103
- Additional Information 104
- Troubleshooting 105
- PORT Status Indicator 106
- MOD Status Indicator 107
- 8-4 Troubleshooting 108
- Troubleshooting 8-5 109
- (version 3.01 or higher) 109
- 8-6 Troubleshooting 110
- Viewing and Clearing Events 111
- 8-8 Troubleshooting 112
- Specifications 113
- Environmental 114
- Regulatory Compliance 114
- Adapter Parameters 115
- B-2 Adapter Parameters 116
- Adapter Parameters B-3 117
- B-4 Adapter Parameters 118
- ControlNet Objects 119
- Identity Object 120
- Identity Object (Continued) 121
- Assembly Object 122
- Assembly Object (Continued) 123
- Register Object 124
- Register Object (Continued) 125
- Parameter Object 127
- Parameter Object (Continued) 128
- Class Code 130
- Services 130
- Instances 130
- Class Attributes 130
- Instance Attributes 131
- (Continued) 131
- PCCC Object 132
- PCCC Object (Continued) 133
- DSI Device Object 138
- DSI Device Object (Continued) 139
- DSI Parameter Object 141
- Descriptor Attributes 143
- Formulas for Converting 144
- Common Services 144
- Object Specific Services 144
- DSI Fault Object 145
- DSI Fault Object (Continued) 146
- DSI Diagnostic Object 147
- Logic Command/Status Words 149
- Logic Status Word 150
- Glossary 151
- D Data Rate 152
- F Fault Action 153
- I I/O Data 153
- L Logic Command/Logic Status 154
- N Node Address 154
- R Reference/Feedback 154
- S Scanner 155
- Z Zero Data 155
- G-6 Glossary 156
Related products and manuals for Equipment Rockwell-automation 22-COMM-C ControlNet Adapter
Equipment Rockwell-automation 20L PowerFlex 700L Frame 2 Common Mode Choke Kit User Manual
(4 pages)
(4 pages)
Equipment Rockwell-automation 20P PowerFlex DC Drive - Frame C AC Line Snubber B User Manual
(16 pages)
(16 pages)
Equipment Rockwell-automation 20P PowerFlex DC Drive - Frame B Pulse Transformer User Manual
(4 pages)
(4 pages)
Equipment Rockwell-automation 20P PowerFlex DC Drive - Frame C Bimetal Thermosta User Manual
(16 pages)
(16 pages)
Equipment Rockwell-automation 140A Manual Motor Starter / Circuit Breaker Instru User Manual
(4 pages)
(4 pages)
Equipment Rockwell-automation 20P PowerFlex DC Drive - Frame D Snubber Resistors User Manual
(10 pages)
(10 pages)
Equipment Rockwell-automation 20P PowerFlex DC Drive - Frame D Overvoltage Clipp User Manual
(4 pages)
(4 pages)
Equipment Rockwell-automation 20P PowerFlex DC Drive - Frame A Field SCR/Dual Di User Manual
(14 pages)
(14 pages)
Equipment Rockwell-automation 20L-LL PowerFlex 700L Liquid-to-Liquid Heat Exchan User Manual
(6 pages)
(6 pages)
Equipment Rockwell-automation 23P PowerFlex DC Stand-Alone Regulator (SAR) Disch User Manual
(10 pages)
(10 pages)
Equipment Rockwell-automation 42GNC_NF_NL_NP_NR_NU SmartSight DeviceNet PHOTOSWI User Manual
(4 pages)
(4 pages)
© 2020, manymanuals.com. All rights reserved. | 0.388 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals