Rockwell-automation 1336T ControlNet Frn1.02 Rev 1.5 User Manual Page 199
- Page / 217
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
7–11Troubleshooting
Publication 1336 FORCE–5.18 ––March, 1999
Fault text and
code:
Suggested action:Description:
Fault
type:
No AP LM Exists
25023
Hard
The ControlNet Adapter Board
has detected that a language
module has not been installed
on the ControlNet Adapter
Board.
Reset the drive. If the fault persists,
replace the language module.
SP Pt1 Timeout
26038
Soft,
warning,
or none
The device connected to Port 1
of SCANport has been
disconnected.
Reconnect Device if desired.
SP Pt2 Timeout
26039
Soft,
warning,
or none
The device connected to Port 2
of SCANport has been
disconnected.
Reconnect Device if desired.
SP Pt3 Timeout
26040
Soft,
warning,
or none
The device connected to Port 3
of SCANport has been
disconnected.
Reconnect Device if desired
SP Pt4 Timeout
26041
Soft,
warning,
or none
The device connected to Port 4
of SCANport has been
disconnected.
Reconnect Device if desired.
SP Pt5 Timeout
26042
Soft,
warning,
or none
The device connected to Port 5
of SCANport has been
disconnected.
Reconnect Device if desired.
SP Comm Fault
26043
Hard
The integrity check on the board
hardware has failed.
Reset the drive. If the fault persists,
replace the ControlNet Adapter Board.
HW Malfunction
34001
Hard
The integrity check on the board
hardware has failed.
Reset the drive. If the fault persists,
replace the ControlNet Adapter Board.
HW Malfunction
34002
Hard
The integrity check on the board
hardware has failed.
Reset the drive. If the fault persists,
replace the ControlNet Adapter Board.
HW Malfunction
34003
Hard
The integrity check on the board
hardware has failed.
Reset the drive. If the fault persists,
replace the ControlNet Adapter Board.
HW Malfunction
34004
Hard
The integrity check on the board
hardware has failed.
Reset the drive. If the fault persists,
replace the ControlNet Adapter Board.
HW Malfunction
34005
Hard
The integrity check on the board
hardware has failed.
Reset the drive. If the fault persists,
replace the ControlNet Adapter Board.
SW Malfunction
34016
Hard
The integrity check on the board
software has failed.
Reset the drive. If the fault persists,
replace the ControlNet Adapter Board.
- 1336 FORCE 1
- ControlNet 1
- Allen-Bradley 1
- Important User Information 2
- Table of Contents 3
- Scheduled Data Transfer 4
- Unscheduled Messaging 4
- Drive Resources 5
- Troubleshooting 5
- Using the Trend Features 6
- Specifications 6
- 8
- Purpose of this Manual 9
- Related Documentation 10
- Terms and Abbreviations 11
- Preface P–5 12
- Common Techniques Used in 13
- Allen-Bradley Support 14
- Catalog Number 14
- Description 14
- Installing and Wiring Your 16
- Contr olNet Adapter Boar d 16
- Mounting the ControlNet 17
- Adapter Board 17
- Setting Your Input Voltage 18
- Writing to BRAM 18
- Terminal Block Locations 18
- Discrete I/O 19
- Analog I/O Connections 21
- Analog Outputs 22
- Determining Your 23
- Communications 23
- Configuration 23
- Fiber Optic Cable 23
- Installation 23
- Module Selection 24
- Starting Up 27
- Setting Up the Analog I/O 30
- 2–5Starting Up 31
- 2–6 Starting Up 32
- DC has been 32
- DC as shown in Figure 2.1 32
- Figure 2.1 32
- 2–7Starting Up 33
- Figure 2.2 33
- 2–8 Starting Up 34
- DC, requires a digital range 34
- Figure 2.3 34
- Using the SCANport 35
- Capabilities 35
- Pre-Configured Links 35
- 2–10 Starting Up 36
- Figure 2.4 36
- 1336 FORCE 36
- Using Scheduled Discr ete 37
- Data Transfer 37
- Discrete PLC Programming 39
- Discrete I/O Program Example 40
- Using Unscheduled Messaging 43
- Message Instruction 44
- ControlNet Command Set 45
- transfer functions 46
- Example 1 47
- Emulated Block Transfer 49
- Message Summary 50
- Parameter Read 51
- Parameter Value Read 52
- Continuous Parameter Value 54
- Parameter Read Full 58
- Parameter Write 60
- Fault Queue 65
- Fault Clear/Reset 66
- Fault Entry Read Full 69
- Warning Queue 70
- Warning Clear 71
- Warning Queue Read Full 73
- EE Memory Request 74
- Save/Recall/Initialize 75
- Link Read 76
- Scattered Parameter Link Read 80
- Link Write 81
- User Text String 87
- User Text String Read 88
- User Text String Write 90
- Clock Data 91
- ASCII Display Values 94
- Run Time Accumulator 95
- Run Time Accumulator Data 96
- Time Stamp 100
- Reference Time Stamp Data 101
- Trend File 103
- Trend Command 106
- Trend Status 108
- Message Operation 110
- Setup Data Full 110
- All Info 113
- Trigger Time 116
- Run File Data 118
- Stored File Data 121
- Trend Parameter Definition 123
- (continued) 126
- This Page Intentionally Blank 127
- Understanding the Resources 128
- Using the SCANport Image 136
- Understanding Function 138
- Using System Resources 141
- Parameters 143
- Parameter Listing 144
- Parameter Files and 146
- File 1 – Startup 147
- File 2 – Communications I/O 148
- File 3 – Velocity Torque 149
- 6–8 Parameters 150
- File 4 – Diagnostics 151
- 6–10 Parameters 152
- Parameter Conventions 153
- Adapter ID 154
- Adapter Version 154
- Channel A DIP Switch 154
- Channel A LED State 154
- Data Input C1 156
- Data Input C2 156
- Data Input D1 156
- Data Input D2 156
- CntlNet Input 0 157
- CntlNet Input 1 157
- CntlNet Input 2 157
- CntlNet Input 3 158
- CntlNet Input 4 158
- CntlNet Input 5 158
- CntlNet Input 6 159
- CntlNet Input 7 159
- SCANport Analog Input 159
- Analog Input 1 160
- Analog Input 2 160
- Analog Input 3 160
- Analog Input 4 160
- Data Output D1 162
- Data Output D2 162
- CntlNet Out 0 162
- CntlNet Out 1 162
- CntlNet Output 2 163
- CntlNet Output 3 163
- CntlNet Output 4 163
- CntlNet Output 5 164
- CntlNet Output 6 164
- CntlNet Output 7 164
- ChA Logic Command Input 165
- Stop Owner 165
- Direction Owner 165
- Start Owner 166
- Jog1 Owner 166
- Jog2 Owner 166
- Set Reference Owner 166
- Local Owner 166
- Flux Owner 167
- Trim Owner 167
- Ramp Owner 167
- Clear Fault Owner 167
- SCANport Analog Output 167
- Analog Output 1 168
- Analog Output 2 168
- Analog Output 3 168
- Analog Output 4 168
- SCANport Analog Select 168
- Analog Input 1 Offset 169
- Analog Input 1 Scale 169
- Analog Input 2 Offset 169
- Analog Input 2 Scale 169
- Analog Input 3 Offset 170
- Analog Input 3 Scale 170
- Analog Input 4 Offset 170
- Analog Input 4 Scale 170
- Analog Output 1 Offset 171
- Analog Output 1 Scale 171
- Analog Output 2 Offset 171
- Analog Output 2 Scale 171
- Analog Output 3 Offset 172
- Analog Output 3 Scale 172
- Analog Output 4 Offset 172
- Analog Output 4 Scale 172
- [Dir Mask] 173
- Clear Fault Mask 174
- Reset Drive Mask 174
- Local Mask 174
- SCANport Default Reference 174
- ICN Fault Select 175
- ICN WarningSelect 176
- SCANport Fault Selection 177
- SCANport Warning Selection 177
- SCANport Fault Status 177
- SCANport Warning Status 178
- Trend Input 1 178
- Trend 1 Operand Parameter X 178
- Trend 1 Operand Parameter Y 179
- Trend 1 Operator 179
- Trend 1 Sample Rate 179
- Trend 1 Post Samples 179
- Trend 1 Continuous Trigger 180
- Trend 1 Select 180
- Trend 1 Status 180
- Trend Output 1 180
- Trend Input 2 181
- Trend 2 Operand Parameter X 181
- Trend 2 Operand Parameter Y 181
- Trend 2 Operator 181
- Trend 2 Sample Rate 182
- Trend 2 Post Samples 182
- Trend 2 Continuous Trigger 182
- Trend 2 Select 182
- Trend 2 Status 182
- Trend Output 2 183
- Trend Input 3 183
- Trend 3 Operand Parameter X 183
- Trend 3 Operand Parameter Y 183
- Trend 3 Operator 184
- Trend 3 Sample Rate 184
- Trend 3 Post Samples 184
- Trend 3 Continuous Trigger 184
- Trend 3 Select 185
- Trend 3 Status 185
- Trend Output 3 185
- Trend Input 4 185
- Trend 4 Operand Parameter X 186
- Trend 4 Operand Parameter Y 186
- Trend 4 Operator 186
- Trend 4 Sample Rate 186
- Trend 4 Post Samples 187
- Trend 4 Continuous Trigger 187
- Trend 4 Select 187
- Trend 4 Status 187
- Trend Output 4 188
- Tr oubleshooting 189
- 7–2 Troubleshooting 190
- 7–3Troubleshooting 191
- 7–4 Troubleshooting 192
- Fault Queues 193
- Warning Faults 194
- Configurable Faults 194
- 7–7Troubleshooting 195
- Fault Code Descriptions 197
- Fault Displays 197
- 7–10 Troubleshooting 198
- 7–11Troubleshooting 199
- 7–12 Troubleshooting 200
- 7–13Troubleshooting 201
- Using the Tr end Featur es 203
- Setting the Trigger 204
- Condition 204
- 8–3Using the Trend Features 205
- Setting the Sampling Rate 206
- Setting the Number of 207
- Post Samples 207
- Setting the Trend Mode 208
- Trending Status 209
- Looking at the Output 210
- Specifications and 211
- Supplemental Information 211
- Software Block Diagram 212
- Hardware Block Diagram 214
- Parameter Cross 215
- Reference––By Number 215
Related products and manuals for Equipment Rockwell-automation 1336T ControlNet Frn1.02 Rev 1.5
Equipment Rockwell-automation 1492-AIFMCE4-F Fused I/O Interface Module for High User Manual
(4 pages)
(4 pages)
Equipment Rockwell-automation 1494V-DS600 - Series D Variable Depth Disconnect S User Manual
(12 pages)
(12 pages)
Equipment Rockwell-automation 1326AB, 1394, 842A Absolute Encoder Feedback Adapt User Manual
(4 pages)
(4 pages)
Equipment Rockwell-automation 1495-N37 - N42 Disconnect Switch Electrical Interl User Manual
(1 pages)
(1 pages)
Equipment Rockwell-automation 1492- 1771-N Series I/O to 1756 ControlLogix I/O User Manual
(20 pages)
(20 pages)
Equipment Rockwell-automation 1494U-HM1_HP1_HS1 Disconnect Handle for Disconnect User Manual
(2 pages)
(2 pages)
Equipment Rockwell-automation MV SMC Flex OEM Components - Gate Driver Test Powe User Manual
(2 pages)
(2 pages)
Equipment Rockwell-automation 900-TC16 Temperature / Process Controller--Italian User Manual
(1 pages)
(1 pages)
© 2020, manymanuals.com. All rights reserved. | 0.229 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals